SimplyLive
2.2 2.1 2.0
2.2 2.1 2.0 English

WebConfig Server Channels

This is the main configuration page for input and output channels.

image-20240318-215324.png

Input channels

Click the + button to the upper right to add channels.

  1. Longname:
    Option to enter a long name for your new input channel

  2. Shortname:
    Option to enter a 3 letter alias for your channel. This is what shows in most of the UI.

  3. Server:
    Drop down to select your server. Networked servers will show all available servers.

  4. SLSM:
    Standard Video or SLSM - Enables multiphase super slomo cameras.

  5. Input Option:
    Drop down to select the type of input for your channel

    1. SDI:
      Serial Digital Interface

      1. SDI input # from capture card

    2. NDI:
      Network Device Interface

      1. NDI option that is detected by the BE

    3. RTP:
      Real-time Transport Protocol

      1. Enter your IP and Port for RTP

    4. SRT:
      Secure Reliable Transport

      1. mode: Caller/Listener/Rendezvous

    5. UDP:
      User Datagram Protocol

      1. Enter your IP, Port and Multicast IP

    6. RTMP:
      Real-time messaging protocol

      1. No options for this when selected

    7. INTERNAL

      1. Train:
        Used for enabled network access program and record trains. When not in network, will not have an internal train, do not select if not in network.

    8. FILE:
      Static file that is on the system for playback, generally this is for testing purposes only.

      1. Enter file paths to Video/audio files EX: C:\\TS1\BASKET6.TS

    9. QUAD:
      4 Quadrant Multiviewer - This is for testing procedure only.

      1. Enter 4 quadrants of current input channels

    10. SNICKO:
      Creates snicko meter out of selected audio track.

      1. Enter Camera input and MONO audio track.

    11. ST2110 :
      Video Streaming Standard over IP

      1. Redundant Video slider: Enables further options for ST2022-7

      2. VIDEO: Local IP | Multicast Source | Group IP | Multicast Port

      3. Redundant Audio slider: Enables further options for ST2022-7

      4. AUDIO: #OF CHANNELS | LOCAL IP | Multicast Source | Group IP | Multicast Port

Output Channels

Please NOTE: You must have 1 output configured to use Reference. Reference must be connected to the same card the output is configured on.

For each output, you’ll have the option to have VITC (vertical interval timecode) and BITC (burnt-in timecode) on or off.

  1. Name:
    Name of the output Channel, Reference only. This is not seen in the UI

  2. SERVER:
    Dropdown to select your server or other servers when networked.

  3. Player:
    Drop down to select a PGM and clean or Dirty.

  4. Output Option:

    1. SDI:
      Serial Digital Interface

      1. SDI output on Video card.

    2. NDI:
      Network Device Interface

      1. NDI Name: Enter a name for the NDI Stream sent from the server

    3. NDI Q200:
      Network Device Interface Quality 200

      1. NDI Name: Enter a name for the NDI Stream sent from the server

    4. RTP:
      Real-time Transport Protocol

      1. IP:
        IP to send the RTP Stream on

      2. Encoder Mode:
        HEVC or .h264

      3. Encoder Hardware:
        GPU/CPU/DISABLE

      4. Video Pixel Type:
        YUV420/YUV422

      5. Video Quality:
        Numerical Value, Default is 8.

      6. Audio Codec:
        AAC/MPEG1 L2

      7. Audio Channels:
        Drop down to configure total audio channels

      8. Audio Quality:
        Drop down to select audio Bit rate.

    5. SRT: Secure Reliable Transport:

      1. MODE:
        Caller/Listener/Rendevous

      2. Encoder Mode:
        HEVC or .h264

      3. Encoder Hardware:
        GPU/CPU/DISABLE

      4. Video Pixel Type:
        YUV420/YUV422

      5. Video Quality:
        Numerical Value, Default is 8.

      6. Audio Codec:
        AAC/MPEG1 L2

      7. Audio Channels:
        Drop down to configure total audio channels

      8. Audio Quality :
        Drop down to select audio Bit rate.

    6. UDP: User Datagram Protocol

      1. IP:
        Enter Multicast IP

      2. PORT:
        Enter port number

      3. Encoder Mode:
        HEVC or .h264

      4. Encoder Hardware:
        GPU/CPU/DISABLE

      5. Video Pixel Type:
        YUV420/YUV422

      6. Video Quality:
        Numerical Value, Default is 8.

      7. Audio Codec:
        AAC/MPEG1 L2

      8. Audio Channels:
        Drop down to configure total audio channels

      9. Audio Quality:
        Drop down to select audio Bit rate.

    7. ST2110: Video Streaming Standard over IP

      1. Redundant Video slider:
        Enables further options for ST2022-7

      2. VIDEO:
        Local IP | Multicast Source | Group IP | Multicast Port

      3. Redundant Audio slider:
        Enables further options for ST2022-7

      4. AUDIO:
        #OF CHANNELS | LOCAL IP | Multicast Source | Group IP | Multicast Port